Servidor Escuchar Puerto de CCcam?

lo que es el servidor Escucha número de puerto de Cccam / Newcamd para lector de tarjetas interno, quiero configurar mi tarjeta Conax personal en ella para que pueda leerlo como locales, no te quiero compartir sobre lo net.so N Línea debo dar en archivo cccam.cfg., cualquier amigo puede ayudarme, he EngelRS4800Y ya parcheado con este firmware
rs4800hd/re-ultimo-firmware-rs4800y-27-01-2014-t179189

yo creo que este deco NO puede hacer de  SERVIDOR, podrás leer la tarjeta , pero no podrás compartirla.

saludos.

What is the server listen port of CCcam / Newcamd for internal card reader, i want configure my personal conax card
in it so that it can communicate between Newcamd>Cccam, i dont want to share on net,
i read on another forum that i have to give N: Line in the cccam.cfg file to make my card read as local via cccam
Can anybody help me write the proper N: Line for cccam listening port number,Thanks.


Newcamd as Reader and Server for Cccam.

Exactamente yo no quiero compartir sólo quiero que lo leyó en la leva embebido

Hi
Then, we don't understand you. The translation is not very good. I understand a little English because  I'm studying English

Hi
Then, we don't understand you. The translation is not very good. I understand a little English because  I'm studying English
 

Thank God atleast I found one who understands little English, ok friend I have no interest in your servers because I am in asia and most of the satellites are out of range, since engel is a Linux box like dreambox I want this Deco for my personal home card use, at present I am watching my card in its paired box, but I read that if I know the boxkey I can make it read in engel, now Conax Cas 7 Cards are well read in Newcamd/Cccam  and Oscam/Cccam one of the forum friend gave me his file of Al-Jazira (irdeto)card which he is using in Engel with Oscam,cfg as a card reader file, but I have to make some changes as per Conax Requirement, so  in the last line of .cfg file I have to give N: Line to make it read as Oscam/Cccam, but I need cccam listen port like 12000 0r 127.0.1 like in dreambox,
I don't know Engel Listen port number, so do you know the port?
 see the pic attached for example

Yo lo que he entendido es que quiere ver por newcccam en su engel conectándose a otro deco que usa conax... Eso puede ser ?

Thanks gatao, you understand what I want to say, actually the word"server"I am using is creating a lot of confusion, over here the word server I am referring to Oscam for serving to Cccam internally,
maam64 gave me this file, which he is using for his Al-Jazira Card(Irdeto) but I don't know whether this will work for my conax card as there is no N:Line

Gracias Gatao, ¿entiendes lo que quiero decir, en realidad la palabra "servidor" [/ b] que estoy utilizando es la creación de una gran confusión, por aquí la palabra servidor me refiero a Oscam para servir a CCcam interno,
maam64 me dio este archivo, que él está utilizando su tarjeta de Al-Jazira (Irdeto), pero no sé si esto funcionará para mi tarjeta Conax ya que no hay N: Line



oscam.server (Debe tener algo similar a esto)
#
# Card Viaccess v4.0 (JSC Sports +1 a +10, HD1 y HD2, Caduca el 31-12-2013)
#
[reader]
label = JSC_HD
Protocol = internal
detect = CD
device = /dev/sci0
mhz = 500
cardmhz = 500
Group = 1
EMMCache = 1,3,2
caid = 0500
ident = 0500:042400,042410,fff920
ecmwhitelist = 0500@042400,042410,fff920:2F,2A

oscam.conf (Debe tener algo similar a esto)
#
[newcamd]
Key = 0102030405060708091011121314
Port = 1000@0500:042400,042410,fff920
keepalive = 1
#
[cccam]
port = 1001
reshare = 3
forward_origin_card = 1
version = 2.1.1
stealth = 1
nodeid = 0A0B0C0D0E0F4321

Hi
According to the image, you must choose a port, username and password and must be the same that contains the configuration file and then you can make  the line that you need.   

This is what I understood you wanted.
 I hope you have served.

Regards