Manual
======================
1.How to update s/w by PC?
======================
1) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver and press "POWER" key to make it standby, the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Main S/W>,press <Open> and select the bin file,then click <Start>,upgrade will begin.
5) After finishing, the LED will display "-End"
======================
2.How to update s/w by USB?
======================
1)copy the bin file in your U disk
2)Plug U disk to the STB.
3)press USB key to go to USB Menu
4)find the bin file in the list and press OK key
=========================================
3.How to Enable Patch or Disable Patch?
=========================================
TV/SAT-->000
=======================
4.How to Edit Patch key?
=======================
After Enable the Patch, go to Main Menu---System Setting-->Accessories--Key Menu
TV/SAT edit TP.
======================
5.How to update the Patch key?
======================
1) Download the softcam.key from the internet.
2) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver and press "POWER" key to make it standby, the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Key>,press <Open> and select the softcam.key file,then click <Start>,upgrade will gin.
5) After finishing, the LED will display "-End"
=================================
6.How to upload the Channel Data?
=================================
a)Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
b)Connect your PC and receiver with twisted RS-232C cable.For safety,you should switch off the computer and the receiver before connection.
c)Turn on the receiver and press "POWER" key to make it standby
d)Run the upgrade tool on your PC, and config your correct COM.
e)Slect the <Upload Data>,then click <Start>,upload will begin.
f)During the uploading,the LED will display "Uxxx"(Upload the data to PC),at last it will display "-End".
g)After uploading,it will generate a file(*.SDX) on the same directry of the update tool[Upgrade],the path name will display on the File Status. This file includes all the satellites, transponders ,channels and settings.
======================
7.How to use PIP funtion?
======================
1)Press Yellow key and choose PIP to enter the list to select another in the same tp.
2)choose one chanel and press ok key .
3)press yellow buttom for help. [A-Z]ZOOM IN,[SAT]ZOOM OUT Small Window,green key swap two channel
======================
8. Ethernet Sharing
======================
a) After factory default,Searching channels .
b) Enable Patch.
c) Press TV/SAT+111 and Select Ethernet Mode
d) Go to Main Menu---Addition-->--IP setting
e) Press green key (auto IP) and the STB will restart to get IP Automatically.
d) Go to Main Menu---Addition--Server setting
In this menu, you can input the server by manul. After input the server, it will automally login the server and display
press blue key to active the server
the server information at the bottom.
======================
9. Hot Keys
======================
info+1: All ECM List
info+0: Current Key
How to test SDS?
1. Connect the W3 on the Tuner2.
2. Connect Nilesat or Horbird or Astra satellite on Tuner1.
3. Searching the channels on Tuner1.
4. TV/SAT+000 to enable patch;
5. TV/SAT+111 to select SDS Mode and Select satellite W3;
6. Restart to check the channel.