Autor Tema: How to setup Universal RCU (Leído 1762 veces)

Perfil · Registrado: 17/01/2008 Gracias: 144/3190 Mensajes 20498

Ruby RCU is a universal RCU that can be used for TV and STB at the same time.

Note: Remember to press Num Lock button on RCU for entering numbers!

User Guide of Ruby Universal RCU

Pre-note:
<< >> means long press
< > means normal press
4 digit code can be found in the TV brand code list at the end of this post.
The new RCU of Ruby is a universal type and you can control your Ruby STB and TV at the same time. This universal RCU is a modeless design. While offering the basic control functions of your TV (TV Power, Volume +/-, Mute, AV), you can control STB without having to select mode between TV and STB every time. Compared to those universal RCU of mode selection types, the modeless universal RCU of Ruby is clearly a smarter choice by eliminating unneeded control functions.

1. TV setting

Set-up Sequence: <<1 + 3>>, <4digit brand-code>, <<Mute or Power>>
1. Press number 1 and 3 for three seconds until LED is on.
2. Find your TV brand-code from the TV code list and insert 4 digit code.
- If you press “0000”, Full Automatic Scan will start. This will take a while.
3. Keep pressing Mute button (or Power) until your TV is muted (or turned off)
4. If your TV is muted (or turned off), stop pressing Mute button.
5. Now, your RCU is in test mode and press Volume + /- to check if your TV responds.
6. If the volume buttons are operational, Press <OK + STOP> to escape from the set-up mode.

2. AV setting

AV button is for the selection of TV video source. AV button may be automatically set up depending on TV models. In case it is not automatically configured, please follow the instructions below.

Set-up Sequence <<1 + 9>>, <<AV>>
1. Press 1 and 9 for three seconds until LED is turned on.
2. Keep pressing AV button until your TV responds and displays the video input source.
3. If AV button is working, check if AV button is properly working several times.
4. Press <OK + STOP> to escape from the set-up mode.

3. RCU Buttons for TV

* Buttons for TV only: TV Power. AV
* Buttons switchable between TV and STB: Volume +/ - and Mute
- These buttons are for STB only before the RCU set-up is done.
- It is switchable only after the configuration is done.
* All the other buttons are for STB only

4. Mode Switch of Volume + / - and Mute

For the sake of easy volume control, please set the STB volume at 50% of the maximum level and set this level as the default volume level from STB. Then, you just have to control your TV volume only without having to adjust STB volume at the same time.
Set-up Sequence: <<1 + 6>>, <9>, <9>, <3>, <TV Power or STB Power>
1. Press 1 and 6 for three seconds until LED is on.
2. Press <9>, <9>, <3>.
3. If you want to control of TV volume, press TV Power button. If you want to control STB volume, press STB Power button.

5. Reset of TV Set-up

In case you want to reset the configured TV set-up of your RCU,
Press Sequence: <<1 + 6>>, <9>, <9>, <6>
1. Press 1 and 6 for three seconds until LED is on.
2. Press <9>, <9>, <6>.
3. This will reverse the RCU into no configuration state.

Tested by paolino on LG TV, code 1628

PS: Thanks to Marusys for infos, and a big thanks to BigEd for input to make this HowTo.